µm, 2 bar). 2. Restauration mit Alkohol reinigen oder dampfstrahlen. 3. Restauration mit öl- und wasserfreier Luft trocknen. 3 4. Geeigneten Primer (z. B. LuxaBond Universal) gemäß Herstellerangaben [...] Kantenreduktion und Feinausarbeitung mit Feinkorn-Diamantschleifer und geringem Anpressdruck durchführen. 3. Konstruktion durch Auftragen von Keramik charakterisieren. Hinweis: Geeignet sind alle Keramiken für [...] Carry out edge reduction and fine-tuning with fine grain diamond miller and low contact pressure. 3. Individualize design by applying ceramic. Note: All ceramics are suitable for zircon constructions
Tipo de arquivo: pdf
Menção em: Instrução para uso
Download
manufacturer’s instructions. 14 2. Apply Luxatemp-Automix Solar to all sur- faces. 3. Hold the parts together for 3 minutes. 4. After 5 minutes, the appropriate points can be finished as usual. Note: [...] istruzioni per l‘uso. 2. Applicare Luxatemp Automix Solar su tutte le superfici. 3. Tenere unite le parti per 3 min. 28 Miscelare il materiale che fuoriesce premendo la leva [F] del dispenser [...] muesca del cartucho coincida con la muesca de la cánula de mezcla. 3. Gire la cánula de mezcla 90° en sentido hora- rio para bloquearla. 3. Presione las partes. 4. Fotocure la parte correspondiente del
Tipo de arquivo: pdf
Menção em: Instrução para uso
Download
2 3 4 5 61 Handling Cartridges C F A B E D Fig. 1 Gebrauchsanweisung Deutsch Produktbeschreibung Bissregistriermaterial auf A-Silikonbasis mit hoher Endhärte. Indikationen • Bissregistrierung [...] Hinweis: Darauf achten, dass die Aussparungen an der Mischkanüle und der Kartusche übereinstimmen. 3. Die Mischkanüle durch Drehen um 90° im Uhrzeigersinn arretieren. Material applizieren ▸ Beim erstmaligen [...] von ca. 5 mm Dicke sollte ausreichen. 2. Den Patienten in die gewünschte Okklusion gehen lassen. 3. Nach 1:30 min das fertige Bissregistrat vorsichtig aus dem Mund entnehmen. Bissregistrat bearbeiten
Tipo de arquivo: pdf
Menção em: Instrução para uso
Download
einem Diamantbohrer (Rauhtiefe ca. 150 μm) aufrauhen. Frakturränder abrunden. 2. Kofferdam legen. 3. Freiliegende Schmelzflächen anätzen. 4. Freiliegende Dentinflächen mit einem geeigneten Haftvermittler [...] (peak-to-valley roughness height: approx. 150 μm). Smooth frac- tured margins. 2. Position the rubber dam. 3. Etch exposed enamel. 4. Apply a suitable bonding agent to exposed dentine. Observe the manufactur- [...] cure and finish the Composite restorative material according to manu- facturer’s instructions. 3 Note: The first Composite layer must be applied directly to the disperson layer using firm pressure
Tipo de arquivo: pdf
Menção em: Instrução para uso
Download
2 3 4 51 Gebrauchsinformation Deutsch Luxatemp-Glaze & Bond ist ein lichthärtendes 1-Komponenten-Material auf der Basis von multifunktionellen Methacrylaten zur Oberflächenversiegelung und Repa- ratur [...] anrauen. 2. Eine dünne Schicht des Materials luftblasenfrei auf die entsprechenden Flächen auftragen. 3. 20 s mit einer Halogenlampe oder ≥ 10 s mit einer LED-Lampe (Lichtintensi- tät > 1000 mW/cm2) belichten [...] cutter. 2. Apply a thin layer of the material to the corresponding surfaces free of air bubbles. 3. Expose to a suitable curing light for 20 seconds with a halogen lamp or ≥ 10 seconds with an LED
Tipo de arquivo: pdf
Menção em: Instrução para uso
Download
nach Mischbeginn einsetzen und mit leichtem Druck auf dem trockenen, präparierten Zahn befestigen. 3. Nach dem Aushärten Zementüberschüsse mit einer Sonde entfernen. Diese lassen sich leicht und in großen [...] within 1:00 min of start of mixing and attach to the dry, prepared tooth using slight pressure. 3. After curing, remove excess cement with a probe. It is easy to remove large chunks of excess cement [...] to direct sunlight! ▸ Close the tube again after use! ▸ Do not use after the expiration date! 3 Composition • Catalyst paste: Natural resins, fatty acids, additives • Base paste: Zinc oxide, paraffin
Tipo de arquivo: pdf
Menção em: Instrução para uso
Download
einem Diamantbohrer (Rauhtiefe ca. 150 μm) aufrauhen. Frakturränder abrunden. 2. Kofferdam legen. 3. Freiliegende Schmelzflächen anätzen. 4. Freiliegende Dentinflächen mit einem geeigneten Haftvermittler [...] (peak-to-valley roughness height: approx. 150 μm). Smooth frac- tured margins. 2. Position the rubber dam. 3. Etch exposed enamel. 4. Apply a suitable bonding agent to exposed dentine. Observe the manufactur- [...] cure and finish the Composite restorative material according to manu- facturer’s instructions. 3 Note: The first Composite layer must be applied directly to the disperson layer using firm pressure
Tipo de arquivo: pdf
Menção em: Instrução para uso
Download
Schützenstr. 3 96047 Bamberg Bamberg
VISUALIZAR